Fluke Kohoutovice

Technology of laying gypsum tiles along with your hands

Gypsum tiles must be laid correctly, as not just the aesthetic look of cosmetic facing, but in addition the service life of this

substance will be dependent on the technologies of job. The product is universal, and it may be attached to plaster, concrete,

brick or gypsum board sheets, provided the top layer of the base is and has no defects.

If the defects of this base are important, it ought to be completely treated with primer, then a cement mortar is created, which

fills all of the cracks. Subsequently the surface ought to be repeatedly primed and dried. In this case, its composition should

decide on a particular, comprising elements which stop the appearance of fungus and mould.

In the modern interior of the rooms most frequently used gypsum tiles, imitating natural stone or brick. To perform cosmetic

finishing yourself, it is necessary first of all to select a strategy of tile placement and prepare a remedy. It’s crucial to pay

attention to the opposite side of the material. If its surface has an embossed surface, then the adhesive should be placed having

an trowel, and if it is even, then with a notched one.

The technology of this job is as follows:

* A thin layer of adhesive mortar is placed on the pre-prepared wall. It is distributed over the bottom so it is likely to place

4-5 tiles. Decorative cladding may be placed either on plasterboard, and on putty.

* Glue the rear side of these tiles with adhesive.

* Plaster components are pushed against the walls and their place is corrected. To align with the seams, it is recommended to

use spacers.

* Finishing is performed in rows, all which should be changed by half of a tile. Facing is carried out into the corners of the

room, then immediately eliminate any remaining mortar in the joints.

Drying the walls requires no more than a day also requires a constant humidity and temperature within the room. The last point in

the placing of gypsum tiles is their own decoration. To do this, the joints between the elements are filled with a special

solution, the color of which matches the brick.

Cosmetic fake of brickwork around the walls is carried out in the following manners:

* Cutting the plastered surface of the stitches of masonry using a bolt cutter with your hands;

* placing of tiles under the brick:

* imitating the format and color of the side of one brick;

* Imitating a fragment of brickwork of several bricks.

The best way to decorate“under the brick“ is really the one which allows you to make a practical coating with the maximum look of

its similarity to organic masonry. All 3 ways to carry out this type of finishing functions fulfill the prerequisites, however,

the cutting of joints using a bolt is more labor-intensive and the creation of considerable amounts of dust, so let us consider

more prevalent manners.

The old finish is removed from the walls, and also the outside, if needed, is leveled to get rid of the need to paste plaster on a

thick layer of adhesive.

Combining these cladding with different kinds of interior finishes could be both orderly and done with no apparent consistency,

chaotically, with fake of indications of aging.

With the support of decorative gypsum tiles it is possible to imitate a lot of textures.

A large number of textures may be imitated with the help of cosmetic gypsum tiles.

The wall where it’s to be set up must possess the following characteristics:

* Hardness and strength of the surface;

* masterfasada.ru The absence of irregular locations and sharp gaps;

* no deformations.

Decorative tiles at the interior of this kitchen

Walls are created from a variety of materials, let us break down the principles of setup.

When dealing with concrete, there’ll be no big problems. It’s only required to take into account the porosity of the material.

Concrete, that has almost no pronounced pores, ought to be treated with a good primer.

Mounting gypsum tiles on concrete

Before beginning work on the installation of gypsum tiles to the walls, then it’s worth assessing the strength of this surface.

When the plaster doesn’t drop off the walls and at the same time holds well, you can simply paint it using primer.

Mount the tiles onto the painted concrete should not. The surface ought to be scratched, making sure to misfire, then it ought to

be grouted and covered with a layer of plaster.

Features of polycarbonate greenhouse Harvest PC

The thickness of this substance is 4 mm.

If you want, you can boost the duration of the structure to 6 yards or longer. To try it, it’s enough to join a two-meter extension. When picking a drawing, look closely at the distance between the arches gidpostroy.ru. This figure must be 65 cm, that’s the most appropriate duration for the specified thickness of the substance. The diameter of the doorways based on the manufacturer’s drawing is 90 cm.

Before assembling a polycarbonate greenhouse, it’s important to select a location because of the place. If that is done properly, you can provide yourself with a harvest of fresh veggies for the entire calendar year.

The place for your upcoming greenhouse is marked immediately in the planning of this garden plot. In order to melt the snow in the place of their greenhouse as early as possible, the ideal point on the site is going to be a small elevation. Additionally, in such a location is not going to need to be concerned about high humidity as dirt and air in the construction.

Build a polycarbonate greenhouse in an elevated site – intends to care for the best temperatures indoors.

If it is not feasible to place a greenhouse in an elevated position, you’ll have to pour a layer of fine crushed stone about 20 cm and the exact same layer of fertile land to make seedbeds.

Before assembling a greenhouse in your backyard plot, it’s also wise to think about where and how this structure is going to be set up. First, you have to pick a place for it. The greenhouse should be found at a metropolitan region at least a couple meters away from houses, barns and other structures.

How to Put in a greenhouse in Line with the Surfaces of the Planet

Make sure you measure the soil surface – it’s ideal to remove the surface. This will also get rid of weed seeds. And for simplicity of work, eliminate the soil in a place that’s around a meter wider on each side of the rectangle that you want.

In addition, it is worth considering having a foundation. As producers state, now most greenhouses do not need that, particularly if they (greenhouses) are utilized just in the spring and summer period. But, seasoned anglers still recommend making at least an elementary foundation from a bar. It’s very simple – it’s enough to connect with each other utilizing metal screws and corners four parts of wood using a cross-section of 10 * 10 cm. The size of such a base ought to be equal to the foundation of their future greenhouse.

Simple bar base

You may also create a strip base of concrete. He is more dependable than a bar base, but demands greater fiscal and labour expenses. Incidentally, the rainwater, that is utilised in winter, without it and do not do without it whatsoever.

Stages of the formation of a strip foundation: a schematic representation

Many manufacturers advise to install greenhouse structures without building a base. Even for this purpose, they equip the framework with specific T-shaped legs, so the construction was securely fixed. However, as practice shows, it’s still required to build a foundation: therefore and the foundation will be more securely fixed and the elements of the basis that are in touch with the soil, will be stored much longer in its initial state.

The main issue is to take care of the material with specific agents to protect the timber from moisture. The substance is generally installed on concrete blocks that are dug into the soil. To get a six-meter arrangement, they need 10 bits: four on each side and one at the center of the ends.

Before you do the greenhouse itself, you need to select the ideal place for this. It has to be an even site, so the framework was found equally, without distortions. It needs to be bright and never obscured by buildings or trees.

How to paint radiator?

Painting cast iron drains – maybe not so difficult that it can not be done on their own, saving a fair quantity of money. Moreover, you will be assured in the quality of the work.

What is required as a way to cope with this endeavor? To qualitatively paint the battery, then you’ll require the perfect paint gidpola.ru, as well as comprehension of some technological“secrets“ of the process . Paints

When painting heating batteries, specific requirements are made to their coating: they have to be resistant to constant exposure to high temperatures, abrasion, in addition to long retain customer properties, that is, an attractive overall look. These compositions are suitable for painting cast iron batteries:

Alkyd enamels.

Pros: when warmed up to 90 levels, they retain strength, do not“peel off“, resistant to abrasion.

Cons: for a long time holds a particular odor, coating quickly turns yellow, can be deformed.

Water-dispersion oil enamels.

Pros: fast drying, no odor after drying, color fastness which may be varied with international tints.

Cons: limited choice – not all enamels within this class can withstand high temperatures.

Acrylic enamels on solvents.

Pros: does not call for pre-treatment before painting heating batteries, resistant to high humidity and temperatures, glossy surface, so long retains its original colour.

Disadvantages: Necessity to use solvent, inability to use universal colors to alter the color shades.

Materials

To paint the battery, then You Have to have, in addition to the selected tooth:

• Cleaner for the paint coating,
• glue,
• primer using anti-corrosive properties and also a pair of brushes.

One brush can not do: for hard-to-reach areas need a small, on a very long handle, because of the outside surfaces fit a wider, that can put the paint more evenly and also help you save time.

Mechanisms of Couch beds

Choosing among the many types of transformation of sofas, you want to take into account whether you wish to recline the bed every day, or just sporadically, when guests come to the house.

The leaflet („Click Clack“)

Mechanism: to unfold the sofa, lift the chair and pull it towards you personally. This is just a reliable, time tested mechanism for folding the sofa.

Pluses

• Three places of the back: sitting, lying down,“flake out“ (the intermediate posture together with half an back).
• Compactness.
• Generally, it is likely to provide a picture drawer.
• The resting location is flat, without“kinks“.

Eurochair

Mechanism: The seat is pulled forwards, expertbrusa.ru after which the trunk of the couch is slowly lowered. In fact, these mechanics of folding sofas and mechanisms is challenging to call: the seat is transferred out by slipping on rails, the back is lowered in manual mode.

Pros of

Durability: the simplicity of this mechanics of folding sofa excludes breakages.
A big selection of sizes.

Large linen drawer because of the lack of internal parts of the mechanism.

Smooth sleeping surface.